Connect Here
CLOVASHIELD ACRYLIC EPOXY ENAMEL - CLEAR BASE - PART A (4:1) 3,02L (2,55L + COLORATION)
Product Code: 83803A01
Description :
ClovaShield is an isocyanate free, two component acrylic epoxy finish that provides a high gloss tile-like appearance
with excellent hardness, chemical and abrasion resistance. Exhibits superior gloss and color retention similar to two
component urethanes. ClovaShield has a "no objection" status with the Canadian Food Inspection Agency for use on
walls, ceilings and floors of registered establishments.
Usages prévus :
Ideally suited as an isocyanate free alternative to 2K Urethanes this product can be used on transportation,
agriculture and oil & gas equipment. Also for use in hospitals, cafeterias, sanitary areas, high traffic public use
facilities, institutions, car washes where a highly chemical, water and weather resistant product is required.
ClovaShield is an isocyanate free, two component acrylic epoxy finish that provides a high gloss tile-like appearance
with excellent hardness, chemical and abrasion resistance. Exhibits superior gloss and color retention similar to two
component urethanes. ClovaShield has a "no objection" status with the Canadian Food Inspection Agency for use on
walls, ceilings and floors of registered establishments.
Usages prévus :
Ideally suited as an isocyanate free alternative to 2K Urethanes this product can be used on transportation,
agriculture and oil & gas equipment. Also for use in hospitals, cafeterias, sanitary areas, high traffic public use
facilities, institutions, car washes where a highly chemical, water and weather resistant product is required.
This Kit Contains:
- CLOVASHIELD ACRYLIC EPOXY ENAMEL - PART B (4:1) 760ML* (x 1)
Use
Ideally suited as an isocyanate free alternative to 2K Urethanes this product can be used on transportation,
agriculture and oil & gas equipment. Also for use in hospitals, cafeterias, sanitary areas, high traffic public use
facilities, institutions, car washes where a highly chemical, water and weather resistant product is required.
Surfaces preparation
All surfaces to be painted must be clean, dry and free of contamination. A tack coat is always recommended. New
fibreglass must receive an SSPC-SP1 Solvent Cleaning prior to painting. Old paint must be in sound condition and
tested for non-lifting. A barrier primer may be required. Primed surfaces should be sanded with 280 - 320 grit paper
prior to top-coating. Non-ferrous metals must be scarified by a sweep blast or other mechanical means.
Recommended primer
STEEL 83021ClovaPrime 21/ 86850 DuraPrime
CONCRETESelf Priming
GALVANIZEDSelf--priming (see Surface Prep)
ALUMINUMSelf--priming (see Surface Prep)
Required tools
AIRLESS SPRAY Speeflo Atlas 30:1 with tip sizes .009" - .013" or equivalent
H.V.L.P. Binks Model Mach 1 92 x 95AP (pressure) or equivalent
CONVENTIONAL Binks Model 95GUN 63CSS X 63PB (pressure) or equivalent
BRUSH / ROLLER Brushing is limited to small areas or for touch up.
How to use
Mixing
Mix base and curing agent separately with good agitation. Add converter or curing agent to base component and mix
thoroughly until homogenous. Allow to react in can for 15 - 20 minutes (induction time). If thinning is necessary or
required, proceed only after recommended induction time has passed. Carefully maintain water traps in all air lines.
Humid conditions can lead to condensation during the curing cycle, resulting in loss of gloss.
Thinner
SP03011 High Flash Naphtha
78004 #4 Thinner
Film thickness
Wet: 3.9 - 5.8 mils
Dry: 2 - 3 mils
Drying time
Limitation
After this product has cured for more than 3 days, the surface will require sanding for adhesion purposes on
subsequent coats. For best results, apply when substrate temperature is above 10oC (50oF) and at a minimum of 3oC
(5oF) above the dew point. Painting should not proceed when the relative humidity is above 85%.
Ideally suited as an isocyanate free alternative to 2K Urethanes this product can be used on transportation,
agriculture and oil & gas equipment. Also for use in hospitals, cafeterias, sanitary areas, high traffic public use
facilities, institutions, car washes where a highly chemical, water and weather resistant product is required.
Surfaces preparation
All surfaces to be painted must be clean, dry and free of contamination. A tack coat is always recommended. New
fibreglass must receive an SSPC-SP1 Solvent Cleaning prior to painting. Old paint must be in sound condition and
tested for non-lifting. A barrier primer may be required. Primed surfaces should be sanded with 280 - 320 grit paper
prior to top-coating. Non-ferrous metals must be scarified by a sweep blast or other mechanical means.
Recommended primer
STEEL 83021ClovaPrime 21/ 86850 DuraPrime
CONCRETESelf Priming
GALVANIZEDSelf--priming (see Surface Prep)
ALUMINUMSelf--priming (see Surface Prep)
Required tools
AIRLESS SPRAY Speeflo Atlas 30:1 with tip sizes .009" - .013" or equivalent
H.V.L.P. Binks Model Mach 1 92 x 95AP (pressure) or equivalent
CONVENTIONAL Binks Model 95GUN 63CSS X 63PB (pressure) or equivalent
BRUSH / ROLLER Brushing is limited to small areas or for touch up.
How to use
Mixing
Mix base and curing agent separately with good agitation. Add converter or curing agent to base component and mix
thoroughly until homogenous. Allow to react in can for 15 - 20 minutes (induction time). If thinning is necessary or
required, proceed only after recommended induction time has passed. Carefully maintain water traps in all air lines.
Humid conditions can lead to condensation during the curing cycle, resulting in loss of gloss.
Thinner
SP03011 High Flash Naphtha
78004 #4 Thinner
Film thickness
Wet: 3.9 - 5.8 mils
Dry: 2 - 3 mils
Drying time
Limitation
After this product has cured for more than 3 days, the surface will require sanding for adhesion purposes on
subsequent coats. For best results, apply when substrate temperature is above 10oC (50oF) and at a minimum of 3oC
(5oF) above the dew point. Painting should not proceed when the relative humidity is above 85%.
Available colors
White, Black, Factory-Mixed and Custom Colors
White, Black, Factory-Mixed and Custom Colors
TECHNICAL SHEET - CLOVASHIELD
MSDS - CLOVASHIELD PART A WHITE
MSDS - CLOVASHIELD PART A CLEAR BASE
MSDS - CLOVASHIELD PART B
MSDS - CLOVASHIELD PART A WHITE
MSDS - CLOVASHIELD PART A CLEAR BASE
MSDS - CLOVASHIELD PART B
Available formats
3.78L (3.02L Part A + 760ml Part B)
3.78L (3.02L Part A + 760ml Part B)