BAR-RUST 235 - JAUNE SÉCURITÉ (DC9400) - 15.14L (4:1)

Utilisation
For use on properly prepared steel or masonry surfaces including immersion (non-potable water)service. Ideal for structural steel, piping, storage tank exteriors, machinery, and equipment in petroleumrefineries, pulp and paper mills, chemical and fertilizer plants, and sewage treatment plants.Performance alternate for Federal Specifications TT-C-550 and TT-C-545. Meets AWWA D102.

Surface preparation
Surfaces must be dry, clean, free of oil, grease, form release agents, curing compounds, laitance, other foreign matter andbe structurally sound. Remove all loose paint, mortar spatter, mill scale, and rust. All direct to metal coatings providemaximum performance over blasted surfaces. There are situations and cost limitations which preclude blasting. Bar-Rust235 was designed to provide excellent protection over less than ideal surface preparation. The minimum standard for nonimmersionservice is SSPC-SP2 or ISO8501-1:2007 St2; for immersion service the minimum standard is SSPC-SP6 orISO8501-1:2007 Sa2. These minimum surface preparation standards apply to steel that has been previously abrasiveblasted, coated and deteriorated. Where very rusty surfaces still remain after cleaning use Pre-Prime 167 Sealer beforeapplication of Bar-Rust 235. All direct to metal coatings provide maximum performance over near-white blasted surfaces. 

New Surfaces:
SteelNew steel surfaces should be initially abrasive blasted to near-white metal surface cleanliness in accordance with SSPCSP10or ISO8501-1:2007 Sa2.5. Blast profile on steel should be at least 2.5 mils (63 microns) in depth and be of a sharp,jagged nature as opposed to a “peen” pattern (typically obtained in shot blasting).

Concrete Block:
Remove loose aggregate and repair voids. Fill with Bar-Rust 235 or Tru-Glaze-WB 4015 blockfiller.

Concrete Floors, Poured Concrete:
Cure at least 30 days. Acid etch or abrasive blast slick, glazed concrete or concrete with laitance. Prime with Pre-Prime 167or Bar-Rust 235

Galvanized Steel
Remove dirt and oils by solvent cleaning or with Devprep 88 Cleaner or other suitable cleaner followed by a thorough waterrinsing. Prime with Devran 203 or Devran 201H epoxy primers for non-immersion. For immersion or severe moisturecondition, abrasive blasting is recommended before priming with this product or Devran 201H epoxy primer.

Previously Painted Surfaces
Old coatings should be tested for lifting. If lifting occurs, remove the coating. Otherwise, scuff sand glossy areas and agedepoxy coatings. Clean aged epoxy or urethane coatings with Devprep 88 Cleaner. Remove cracked and peeling paint.Prime bare areas with appropriate primer. If thinning is required, use International GTA007 only when used over aged alkydcoatings.

Recommanded systems
The following primers are recommended for Bar-Rust 235:
Bar-Rust 235
Cathacoat 302H
Cathacoat 302HB
Cathacoat 304L
Cathacoat 304V
Cathacoat 313
Cathacoat 316
Devran 201H
Devran 203
Pre-Prime 167
Tru-Glaze-WB 4015

The following topcoats are recommended for Bar-Rust 235:
Devthane 349QC
Devthane 359
Devthane 359H
Devthane 378
Devthane 378H
Devthane 379
Devthane 379H
Devthane 389N
Devthane 389H

Application conditions

Required tools
Airless spray
Recommended
Tip Range 19-25 thou (0.48-0.63 mm)Total output fluid pressure at spray tip not less than 3000 psi(211 kg/cm²)

For airless spray application: Use an airless spray pump capable of 3,000 psi (207 bars) and .019” to .025” tip sizewill provide a good spray pattern. Ideally, fluid hoses should not be less than 3/8” ID and not longer than 50 feet toobtain optimum results. Longer hose length may require an increase in pump capacity, pressure, and/or thinning.

Air spray
suitable
For air spray application: Use a fluid tip of .070'' or larger, a professional grade conventional gun and an air cap withgood break-up. The fluid pressure should be kept low with just enough air pressure to get good break-up of thecoating. Excessive air pressure can cause over-spray problems.

Brush & roller
suitable

How to use
Mixing
Material is supplied in two containers as a unit. Always mix a complete unit in the proportionssupplied. Once the unit has been mixed it must be used within the working pot life specified.
(1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base(Part A) and mix thoroughly with power agitator.

Thinning is not normally required or desired; however, at extreme environmental conditions, small amounts (15% orless by volume) of International GTA220 can be added depending on local VOC and air quality regulations. Whenusing Bar-Rust 235 over aged alkyds, use International GTA007. Any solvent addition should be made after the twocomponents are thoroughly mixed.

Mix ratio
4 part(s) : 1 part(s) by volume

Working pot life
23°F (-5°C) 41°F (5°C) 59°F (15°C) 77°F (25°C)
6 heures 5 heures 5 heures 4,5 heures

Drying time


Cleaning tools
Clean all equipment immediately after use with International GTA415. It is good workingpractice to periodically flush out spray equipment during the course of the working day.Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time,including any delays. 

Warning
Work stoppages : Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush allequipment with International GTA415. Once units of paint have been mixed they should not beresealed and it is advised that after prolonged stoppages work recommences with freshly mixedunits.

All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

Bar-Rust 235 may yellow during application and cure if exposed to the combustion by-products of improperly ventedfossil fuel burning heaters.