Connect Here
SUPER HIDING INTERIOR LATEX PRIMER-SEALER 3,78L
Product Code: 870-130-1GL
Description :
Latex base primer-sealer specially formulated for interior surfaces: new gypsumboard, new dry plaster, plaster repairs and masonry.
Advantages
• Excellent hiding power.
• Easy to apply.
• Effectively seals and gives the finishing coats a better appearance.
• Will not raise fibres of gypsum boards.
• Can easily be sanded.
• Water-based product which allows tool clean-up with water.
• Low VOC content complies with the Canadian Volatile Organic Compound (VOC)Concentration Limits for Architectural Coatings Regulations requirements.
Latex base primer-sealer specially formulated for interior surfaces: new gypsumboard, new dry plaster, plaster repairs and masonry.
Advantages
• Excellent hiding power.
• Easy to apply.
• Effectively seals and gives the finishing coats a better appearance.
• Will not raise fibres of gypsum boards.
• Can easily be sanded.
• Water-based product which allows tool clean-up with water.
• Low VOC content complies with the Canadian Volatile Organic Compound (VOC)Concentration Limits for Architectural Coatings Regulations requirements.
Environment
Interior only.
Use
Residential and commercial sites.
Surfaces
New surfaces: drywall boards (conventional, water repellent or fire retardant), hardened and dry drywall compound, new dry plaster, concrete, brick, stucco or other masonries. New and maintenance work. Walls and ceilings of any room.
Systems recommandation according to surfaces
Gypsum board, dry joint cement or stucco:
• Sico Expert primer 870-130.
• Sico Expert interior top coats of your choice; two coats.
Concrete and masonery :
• Sico Expert primer 870-130.
• Sico Expert interior top coats of your choice; two coats.
Surface Preparation
Surface should be dry, clean, free from dust, oil, loose paint or all other contaminants
Notes
Must be coated with a topcoat.
This product is not to be mixed with other paints or thinners.
Do not apply directly over steel, iron or other metals.
Not formulated to be used on floors.
Avoid using zinc sulphate solutions on plaster prior to applying this primer-sealer.
Do not use over aged alkyd finishes.
Certifications*
MPI #50 Primer-Sealer, Latex, Interior
Interior only.
Use
Residential and commercial sites.
Surfaces
New surfaces: drywall boards (conventional, water repellent or fire retardant), hardened and dry drywall compound, new dry plaster, concrete, brick, stucco or other masonries. New and maintenance work. Walls and ceilings of any room.
Systems recommandation according to surfaces
Gypsum board, dry joint cement or stucco:
• Sico Expert primer 870-130.
• Sico Expert interior top coats of your choice; two coats.
Concrete and masonery :
• Sico Expert primer 870-130.
• Sico Expert interior top coats of your choice; two coats.
Surface Preparation
Surface should be dry, clean, free from dust, oil, loose paint or all other contaminants
- Clean surface with Polyprep cleaner 771-135, 771-136, or the appropriate cleaner for removing the contaminant. Rinse well. - Remove mildew with a solution of household bleach (1 part household bleach to 3 parts of water). Wear rubber gloves and eye protection. Rinse thoroughly with clear water and let dry completely.
- Strip, scrape or remove all loose and peeling paint, and sand to smooth edges.
- Lightly sand glossy areas. Eliminate sanding residues. Touch up bare spots. Precaution: Dry sanding, flame cutting and/or welding of dry paint film will give rise to dust and/or hazardous fumes. Wet sanding should be used, wherever possible. If exposure cannot be avoided by the provision of local exhaust ventilation, suitable respiratory protective equipment should be used.
- Repair holes and cracks with joint compound suitable for the surface to be repaired
- Once the surface is dry and free of any contaminant, apply the product following the recommended application conditions.
Application Conditions
Temperature: 10 to 32°C (50 to 90°F)(ideal 20°C ± 5°C [68°F ± 9°F]).
Relative humidity: Ideal between 15 and 50%,maximum 85%.High humidity or low temperatures extenddrying time.
Conditions to be observed during both productapplication and drying time.
Tools
• Paintbrush: Synthetic bristles (nylon,polyester).
• Roller: 10 mm (3/8 in.).
• * Spray (airless equipment)- Tip size: 0.015 to 0.021 in.;- Pressure: 1500 to 2000 psi.Always use top quality application tools.* Spray recommendations may vary fromfigures listed depending on equipmentmanufacturer.
Cleaning tools
Remove as much product quantity as possibleand clean tools with lukewarm soapy waterimmediately after use.
Temperature: 10 to 32°C (50 to 90°F)(ideal 20°C ± 5°C [68°F ± 9°F]).
Relative humidity: Ideal between 15 and 50%,maximum 85%.High humidity or low temperatures extenddrying time.
Conditions to be observed during both productapplication and drying time.
Tools
• Paintbrush: Synthetic bristles (nylon,polyester).
• Roller: 10 mm (3/8 in.).
• * Spray (airless equipment)- Tip size: 0.015 to 0.021 in.;- Pressure: 1500 to 2000 psi.Always use top quality application tools.* Spray recommendations may vary fromfigures listed depending on equipmentmanufacturer.
Cleaning tools
Remove as much product quantity as possibleand clean tools with lukewarm soapy waterimmediately after use.
Notes
Must be coated with a topcoat.
This product is not to be mixed with other paints or thinners.
Do not apply directly over steel, iron or other metals.
Not formulated to be used on floors.
Avoid using zinc sulphate solutions on plaster prior to applying this primer-sealer.
Do not use over aged alkyd finishes.
Certifications*
MPI #50 Primer-Sealer, Latex, Interior
Available color :
870-130 White
870-130 White
| Catégorie : | Professionnal paint |
| Marque : | SICO Expert |
| État physique : | Liquid |
| Base : | Water |
| Composition : | N/A |
| Liant : | Vinyl-Acrylic polymer emulsion |
| COV : | According to ASTM D3960-05: < 100 g/L Canadian regulation: < 200 g/L |
| Provenance : | N/A |
| Durabilité : | N/A |
| Pouvoir couvrant : | 460 à 515 ft2 |
| Épaisseur film requis mouillé : | 3,1 mils (79 μm) |
| Épaisseur film requis sec : | 1,2 mil (30 μm) |
| Dilution : | water |
| Temps de séchage au toucher : | 20 to 30 minutes |
| Temps de séchage hors poussière : | 2 to 4 hours |
| Temps de séchage avant de recouvrir : | N/A |
| Durcissement complet : | N/A |
| Odeur : | N/A |
| Aspect : | Opaque |
| Lustre : | N/A |
| % solide volume : | 38% |
| % solide poids : | 58% |
| Densité : | 1,3 ± 0,1 kg/L |
| Viscosité : | Ready to use (96 ± 5 Krebs Units) |
| Inflammabilité : | Non-flammable |
| Point d'éclair : | N/A |
| Entreposage : | Keep product in a dry area between 10 and 30°C (50 and 86°F). AVOID FREEZING. |
| Conservation : | Under such conditions, unopened containers may be stored up to 5 years from manufacturing date. |
| Nettoyage des outils : | Lukewarm soapy water |
| Compatibilité : | Sico Expert top coat of your choice |
| Informations d’urgence relatives aux déversements : | N/A |
Formats :
Gallon - 3.78L
5 Gallons - 18.9L
Gallon - 3.78L
5 Gallons - 18.9L