Connect Here
VELVET FINISH 100% ACRYLIC INTERIOR LATEX PAINT - 18,9L
Product Code: 873-620-5GL
Description :
Peinture d’intérieur pour murs et plafonds des salons, chambres et passages où
un fini peu lustré est recherché.
Sur les surfaces qui nécessitent des lavages fréquents, utiliser de préférence un
fini plus lustré et sur les plafonds de dimensions supérieures à la moyenne, un fini
plus mat.
Avantages
• Fini velouté correspondant aux plus récentes tendances en matière de
décoration.
• Application facile.
• Sèche rapidement et ne dégage que peu d'odeur.
• Aucun apprêt n'est requis sur les surfaces déjà peintes.
• Produit à base d'eau qui permet de nettoyer les outils à l’eau.
• Faible teneur en composés organiques volatils (COV); respecte les exigences du
règlement canadien limitant la concentration en COV des revêtements
architecturaux.
Projets
Environnement
Intérieur seulement.
Utilisation
Travaux neufs et travaux d'entretien.
Murs de salons, passages et chambres à coucher.
Plafonds de toutes les pièces de la maison.
Sites résidentiels et commerciaux.
Surfaces
Surfaces convenablement apprêtées : panneaux de gypse ou de fibres, bois,
béton ou stuc.
Surfaces déjà peintes en bon état et convenablement préparées.
Remarques
Certaines couleurs ou des changements drastiques de couleurs peuvent
nécessiter une couche additionnelle de peinture.
Ne pas mélanger à d'autres peintures ou diluants.
Ne pas appliquer directement sur les métaux ferreux nus (fer, acier).
N'est pas conçu pour être utilisé sur des planchers.
Sur les murs de cuisines et salles de bains, il est préférable d'utiliser un fini plus
lustré.
Peinture d’intérieur pour murs et plafonds des salons, chambres et passages où
un fini peu lustré est recherché.
Sur les surfaces qui nécessitent des lavages fréquents, utiliser de préférence un
fini plus lustré et sur les plafonds de dimensions supérieures à la moyenne, un fini
plus mat.
Avantages
• Fini velouté correspondant aux plus récentes tendances en matière de
décoration.
• Application facile.
• Sèche rapidement et ne dégage que peu d'odeur.
• Aucun apprêt n'est requis sur les surfaces déjà peintes.
• Produit à base d'eau qui permet de nettoyer les outils à l’eau.
• Faible teneur en composés organiques volatils (COV); respecte les exigences du
règlement canadien limitant la concentration en COV des revêtements
architecturaux.
Projets
Environnement
Intérieur seulement.
Utilisation
Travaux neufs et travaux d'entretien.
Murs de salons, passages et chambres à coucher.
Plafonds de toutes les pièces de la maison.
Sites résidentiels et commerciaux.
Surfaces
Surfaces convenablement apprêtées : panneaux de gypse ou de fibres, bois,
béton ou stuc.
Surfaces déjà peintes en bon état et convenablement préparées.
Remarques
Certaines couleurs ou des changements drastiques de couleurs peuvent
nécessiter une couche additionnelle de peinture.
Ne pas mélanger à d'autres peintures ou diluants.
Ne pas appliquer directement sur les métaux ferreux nus (fer, acier).
N'est pas conçu pour être utilisé sur des planchers.
Sur les murs de cuisines et salles de bains, il est préférable d'utiliser un fini plus
lustré.
This Kit Contains:
- ECO FEE 18.9L* (x 1)
Environment
Interior only
Use
New and maintenance work.
Residential and commercial sites.
Living room, hallway and bedroom walls.
Ceilings of any room.
Surfaces
Properly primed surfaces: drywall and fibre boards, wood, concrete, or stucco.
Previously painted surfaces in good condition and properly prepared.
Systems recommendation according to surfaces
Gypsum board, dry joint cement or stucco:
• 1 coat: Sico Ecosource 850-130, Sico Expert 870-130, 870-177 or 870-799;
• 2 coats: Sico Expert 873-6XX.
Concrete or masonry:
• Rough surfaces: Sico Expert block filler 675-115 or 675-198;
• Smooth surfaces: Sico Ecosource 850-130, Sico Expert 870-130, 870-177 or 870-799;
• 2 coats: Sico Expert 873-6XX.
New or bare wood:
• Bare wood (except rich in tannins wood, such as cedar or redwood): Sico Ecosource 850-130, Sico Expert 870-177 or 890-114;
• Bare wood (all): Sico Expert primer 890-114; some wood species, prone to staining, may require two coats.
• 2 coats: Sico Expert 873-6XX.
Ferrous metal and rusted galvanized metal:
• 1 coat: Sico Expert 922-060;
• 2 coats: Sico Expert 873-6XX.
Non-rusted galvanized metal, aluminum or copper:
• 1 coat: Corrostop Ultra 635-045 or Polyprep 145-011;
• 2 coats: Sico Expert 873-6XX.
Previously painted metal in good condition:
• Previously painted surfaces in good condition (latex): No primer is required.
• Previously painted surfaces in good condition (alkyd): Sico Expert primer 890-114 or 870-
177.
• Sico Expert 873-6XX, one or two coats as required.
Surfaces preparation
Surfaces must be clean, solid and dry. Remove all dust, dirt, oil, soot, wax, mildew, chalking, loose paint and other surface contamination.
Application conditions
Temperature: 10 to 32°C (50 to 90°F) (ideal 20°C ± 5°C [68°F ± 9°F]).
Relative humidity:Ideal between 15 and 55%, maximum 85%.
Conditions to be observed during both product application and drying time.
Tools :
• Paintbrush: Synthetic bristles (nylon, polyester).
• Roller: 13 mm (1/2 in.).
• * Spray (airless equipment)- Tip size: 0.015 to 0.021 in.;
- Pressure: 1500 to 2000 psi.
Always use top quality application tools.
* Spray recommendations may vary from figures listed depending on equipment manufacturer.
Remarques
This is a ready-to-use product, do not thin. Stir thoroughly before application.
Pour the quantity of paint needed into another container to avoid contaminating the original paint container. Keep containers closed when not in use.
Apply the product by complying with its spreading rate, leaving no bare spots or excessively coated areas.
Provide adequate ventilation. Observe drying time between coats. Low temperatures or high humidity will affect drying time. Applying two coats will provide better durability and appearance.
Certifications
MPI #44 Latex, Interior, (MPI Gloss 2)
Interior only
Use
New and maintenance work.
Residential and commercial sites.
Living room, hallway and bedroom walls.
Ceilings of any room.
Surfaces
Properly primed surfaces: drywall and fibre boards, wood, concrete, or stucco.
Previously painted surfaces in good condition and properly prepared.
Systems recommendation according to surfaces
Gypsum board, dry joint cement or stucco:
• 1 coat: Sico Ecosource 850-130, Sico Expert 870-130, 870-177 or 870-799;
• 2 coats: Sico Expert 873-6XX.
Concrete or masonry:
• Rough surfaces: Sico Expert block filler 675-115 or 675-198;
• Smooth surfaces: Sico Ecosource 850-130, Sico Expert 870-130, 870-177 or 870-799;
• 2 coats: Sico Expert 873-6XX.
New or bare wood:
• Bare wood (except rich in tannins wood, such as cedar or redwood): Sico Ecosource 850-130, Sico Expert 870-177 or 890-114;
• Bare wood (all): Sico Expert primer 890-114; some wood species, prone to staining, may require two coats.
• 2 coats: Sico Expert 873-6XX.
Ferrous metal and rusted galvanized metal:
• 1 coat: Sico Expert 922-060;
• 2 coats: Sico Expert 873-6XX.
Non-rusted galvanized metal, aluminum or copper:
• 1 coat: Corrostop Ultra 635-045 or Polyprep 145-011;
• 2 coats: Sico Expert 873-6XX.
Previously painted metal in good condition:
• Previously painted surfaces in good condition (latex): No primer is required.
• Previously painted surfaces in good condition (alkyd): Sico Expert primer 890-114 or 870-
177.
• Sico Expert 873-6XX, one or two coats as required.
Surfaces preparation
Surfaces must be clean, solid and dry. Remove all dust, dirt, oil, soot, wax, mildew, chalking, loose paint and other surface contamination.
- Clean with Polyprep cleaner 771-135, 771-136, or an appropriate cleaner for removing the contaminant. Remove mildew with a solution of household bleach (1 part household bleach to 3 parts of water). Wear rubber gloves and eye protection.
- Rinse thoroughly with clear water and let dry completely.
Metal: Remove all loose rust. Treat with a metal conditioner and rust remover and apply a
suitable system for metal. - Strip, scrape or remove all loose and peeling paint, and sand to smooth edges.
- Sand rough areas and dull glossy surfaces. Eliminate sanding residues. Touch up bare spots. Precaution: Dry sanding, flame cutting and/or welding of dry paint film will give rise to dust and/or hazardous fumes. Wet sanding should be used, wherever possible. If exposure cannot be avoided by the provision of local exhaust ventilation, suitable respiratory protective equipment should be used.
- Repair holes and cracks with joint compound suitable for the surface to be repaired.
- If wood exudes resin, scrape the excess and clean with alcohol or paint thinner. Sand for a smooth finish. Eliminate sanding residues. Seal knots with Polyprep shellac 205-112 before applying the primer.
- For optimal results, especially on tough stains or on very porous or absorbent repairs, it is recommended to apply a base coat. Before its application, cover or mask surfaces that are not to be painted.
Application conditions
Temperature: 10 to 32°C (50 to 90°F) (ideal 20°C ± 5°C [68°F ± 9°F]).
Relative humidity:Ideal between 15 and 55%, maximum 85%.
Conditions to be observed during both product application and drying time.
Tools :
• Paintbrush: Synthetic bristles (nylon, polyester).
• Roller: 13 mm (1/2 in.).
• * Spray (airless equipment)- Tip size: 0.015 to 0.021 in.;
- Pressure: 1500 to 2000 psi.
Always use top quality application tools.
* Spray recommendations may vary from figures listed depending on equipment manufacturer.
Remarques
This is a ready-to-use product, do not thin. Stir thoroughly before application.
Pour the quantity of paint needed into another container to avoid contaminating the original paint container. Keep containers closed when not in use.
Apply the product by complying with its spreading rate, leaving no bare spots or excessively coated areas.
Provide adequate ventilation. Observe drying time between coats. Low temperatures or high humidity will affect drying time. Applying two coats will provide better durability and appearance.
Certifications
MPI #44 Latex, Interior, (MPI Gloss 2)
Available colors
Pur WHITE
All the colors of SICO
Please enter your color choice when placing the order
Consult the colors on the SICO website
Pur WHITE
All the colors of SICO
Please enter your color choice when placing the order
Consult the colors on the SICO website
Available formats
3.78L et 18.9L
3.78L et 18.9L